Anyone who owns, or has owned, a two stroke outboard would have asked themselves the question; how much oil do I mix with my fuel? 100:1, 50:1 or 25:1?It is one of the most asked questions for those required to pre-mix their oil and fuel together. Below I have listed the oil ratios regimpppa.orgmended by manufacturers and a few tips based on my experience.

You are watching: Yamaha 115 outboard oil to gas ratio

100:1 - Mix 50ml of oil per 5ltrs of fuel. Regimpppa.orgmended by Yamaha and Suzuki for most of their small two stroke engines up to about 30hp, this ratio requires the least amount of TCW3 two stroke oil. The result of using this ratio (less oil) is reduced spark plug fouling and less smoke.For older Suzuki outboards, pre-1997, I"d regimpppa.orgmend running 50:1 as the information I"ve provided about is for current model two strokes.Note: For gimpppa.orgmercial applications Suzuki regimpppa.orgmends 50:1.50:1 - Mix 100ml of oil per 5ltrs of fuel.Regimpppa.orgmended by Mercury, Mariner, Tohatsu, Johnson and Evinrude this is my preferred ratio for all outboards including Yamaha and Suzuki. You can confidently use this ratio for any horse power and just about all year models. Whilst this ratio might see spark plugs fouling with extended use at lower RPM (such as trolling), in my opinion, it provides the best amount of lubrication for your outboard.25:1 - Mix 200ml of oil per 5ltrs of fuel.This mixture is very rich and is usually regimpppa.orgmended for running in brand new two stroke outboards and when running in rebuilt or reconditioned engines.If you have a rebuilt or reconditioned oil injected two stroke outboard (excluding Evinrude ETEC or Mercury Optimax) then you"ll just need to add 50:1 to your fuel and let the oil injection system add the rest of the oil to make up the balance to get to 25:1.Most technicians will have their own opinion or view on how long you should run the 25:1 ratio for but, I always regimpppa.orgmend between 8 and 10 hours. Unfortunately, you will foul plugs at this ratio and leave a very impressive smoke plume on engine start up but, outboards that have been rebuilt or reconditioned need this extra oil while the piston rings bed into the bores.Oil ratios can be confusing and daunting. The last thing anyone wants to do is not use enough oil and damage their pride and joy.Hopefully, the above answers any questions you may have and gives you a better understanding of what ratio your outboard requires.Shop for Penriteoutboard oils & lubricants here.

gimpppa.orgments (7)

We mixed 25:1 for old 70hp evenrude motor ran ok. On trailer reved alright and ideld ok but on water motor kept dieing and cutting out when starting to load power up could this problem just be too much oil mixOutboard Spares Response Hi,This could be a number of issues such as faulty fuel pump, carburetors needing cleaning, ignition issue, etc. I think running 25:1 will not be the issue with this engine.
Hi guys please assist. I have these two motors however do not know the fuel mixture as some old small motors use to run a 100:1 ratios where as most are 50:1. How will I know. I also do know that fully synthetic has its own mixture like 75:1.

See more: Godzilla Destroy All Monsters Melee Unlock Characters, Godzilla: Destroy All Monsters Melee

Outboard Spares Response Hi,If I owned one of these engines I'd be running 50:1 with a decent TCW3 2 stroke engine oil designed for pre-mix. If you're doing a lot of idling and slow trolling you could reduce the ratio a bit if you found you are fouling plugs but honestly I think 50:1 should be fine.Cheers
A Great Rule Of Thumb on 2 stroke oilsmall engines = less oil 100-1 / 50-1Engines before 2000 and beyond large or small 50-1new engines 25-1 / 20 to 40 liters
Are you able to use the same oil as for aircooled engines such as chainsaws etcOutboard Spares Response Hmmm. Good question. Outboard oils are designed for water-cooled engines. I would not suggest it. Cheers
Is the said ratios needed for large hp 2 strokes . Year 2000 forward . As Most are oil injected anyway .What's the reason for adding oil to the fuel mix if the motor is running fine . No rebuild ect . Dose it save oil being injected .Outboard Spares Response If your outboard is oil injected, and hasn't been rebuilt, then you won't need to add any oil to your fuel. But adding oil to your fuel will not change the amount injected by the engines oil injection system.
Simple divide 1000ml or 1 litre of petrol by ratio = the required amount of oil per litre of fueli.e 1000 / 50:1 = 20ml of oil per litre of fuelOr I.e 1000 ml of petrol divide by 100:1= 10mls of oil per litre