Recoil pullcords are the old school an approach of starting tiny engines and also pull cords arestill being provided in newer leaf blower models. Pull cord device is attacheddirectly to the engine of her leaf blower and also as you pull the starter cord, it reasons the engine to revolve over and start running.But a common issue with the traction cords is that sometimes your sheet blower’spull cord will obtain stuck and also it won’t pull. When a traction cord it s okay stuck, her leaf blower will certainly not start until you settle theproblem. For this reason how can you fix a sheet blower as soon as the pull cord won’t pull?

The sheet blower pull cord that is stuck can be repaired through fixing one of the following problems:

The traction cord has gained tangled or damaged Oil is trapped in the leaf blower’s burning chamber resulting in a hydrolockSpring within the pull starter assembly is not functioning properlyThe engine has actually seized

Your sheet blower’s traction cord might be complicated to traction due to any of the above-mentioned problems and to gain to the root of the problem, girlfriend will need to carefully check your leaf blower’s recoil starter mechanism. It deserve to be difficult to uncover information about fixing a sheet blower starter cord the doesn’t pull. The is why in this write-up we room going to guide you on just how you deserve to repair a stuck traction cord on your leaf blower.


Contents

1 Tangled or damaged traction cord2 Oil in the combustion chamber causinga hydro lock3 Spring inside the pull starterassembly is not working properly

Tangled or damaged traction cord

This is themost common reason for a stuck pull cord. The cord can obtain tangled onto itselfor somewhere inside the traction starter housing. A tangled traction cord is eithergoing to no pull at every or the is walk to pull halfway until it it s okay stuckagain. If a traction cord is no pulling the end fully,it won’t be able to turn the engine enough to begin it up. Luckily, untanglingthe pull cord is not too an overwhelming and every you need to do is access the pullcord by remove the pull starter housing. Yet the procedure of removed the pullstarter housing and the traction cord can vary. Either method here is how you canrepair a tangled up sheet blower pull cord the is not pulling:

Step 1

The an initial thing is, you have to remove the traction starter real estate to accessibility the tangled or damaged traction rope. Now there are a few ways to remove the traction starter housing of her leaf blower. In part leaf blowers, you have the right to simply eliminate the pull starter housing directly without having to remove the side cover by remove the screws holding the traction cord real estate in place. If in part leaf blower models the traction starter device is situated inside the side cover i beg your pardon can additionally be removed easily by remove 3-4 screws hold the side cover in place. Then part leaf blowers call for you to take apart the impeller and the engine cover to access the pull starter housing. You deserve to refer to the user hands-on of her leaf blower to locate and remove the pull starter assembly.

You are watching: Leaf blower cord won t pull


Step 2

With the starter cord assembly removed, examine the pull cord to watch if there is a node or if the cord is tangled onto chin or if it may have come off the reel ~ above which the is claimed to wrap about when the pull cord retracts. You can use a screwdriver to help you in untangling a badly tangled pull rope. If you an alert strands coming off the pull rope, climate it is a sign that the pull rope is damaged and also needs replacing since the strands can get caught inside the starter mechanism and also make it challenging to traction the rope. If you have to replace the damaged traction cord (you can uncover pull cords here) you deserve to do that making use of the complying with method:

Use pliers to eliminate the damaged pull cord indigenous the reel and also get a replacement traction rope with the exact same thickness as the old one. Placed the new cord through the exact same hole in the pull starter reel whereby you took the old rope out from. Make sure to placed the rope v the peak of the rope so that comes the end from the bottom. Tie a knot at the end of the rope after placing it through the feet to prevent it from slipping out, making sure that there is a little rope left after the knot together possible. You can reduced off the overabundance rope ~ the knot to prevent the extra rope from gaining stuck. Currently put the other finish of the rope v the inside of the feet in the traction cord real estate so the it comes the end of the traction cord housing. This is the end you are going to attach the pull handle too.

Note: some pull starters have a screw on the reel for sure the cord along with a hole. So if that is the instance with your leaf blower, make certain to placed the cord around this screw together well.

You can find replacements traction cords or full Starter Assembly here.

Step 3

Finally, all you have to do is simply wind the pull starter device up till the rope winds up onto the reel and also if you mounted a brand-new pull cord, simply affix the manage at the other finish of the rope exterior the pull cord assembly housing.


Step 4

Test the pull cord assembly by pulling the rope a couple of times to watch if it traction without sticking and simply reattach the pull cord assembly housing back onto the sheet blower.

Make surenot to leave extra cord hanging after tying the knot v the starter wheel asthis can also result in the cord acquiring tangledand friend will have to repeat the whole procedure all over again. As soon as installingthe new rope, make sure to cut the correctlength of brand-new rope so the there isn’t any extra rope hanging after the pullstarter assembly winds up. And also you can do the by attaching the pull handle insuch a method that there is no limp rope left outside of the pull starter housing.

Oil in the burning chamber causinga hydro lock

Sometimestoo lot oil deserve to make its method into the burning chamber or the head cylinderof a sheet blower the it no leave any type of room for the piston to move insidethe combustion chamber. This script is recognized as hydro lock together it stop thepiston indigenous moving. A hydro locked leaf blower is no going to permit you come pullthe starter cord at all. If you want to be certain that it is the hydro lockthat is not permitting you to traction the starter rope, lookfor indications of engine oil leakage from the exhaust of leaf blower. If the headcylinder that a sheet blower has actually too much oil in it,then the will shot to seep the end from the exhaust. Currently the engine oil have the right to make itsway into the burning chamber due to manyreasons. You might have overfilled the engine oil reservoir resulting in the engineoil to acquire inside the combustion chamber. Or you can have simply held theleaf blower in an awkward position that might have caused oil come seep right into thecombustion chamber.

No matter whatcaused the engine oil to with the burning chamber, itis crucial to eliminate it if you want to be able to start your leaf blower. Youcan repair a hydro locked leaf blower engine by adhering to these basic steps:


Step 1

To eliminate the overfill oil in the combustion chamber of your leaf blower’s engine, you have to remove the sparkplug and also drain the oil with the sparkplug hole. To eliminate the sparkplug of her leaf blower you need to locate the first. Luckily most leaf blowers have their sparkplug situated such that you have the right to remove castle without having to remove any type of protective covers. In the majority of cases, you will find the sparkplug on peak of the sheet blower near the handle.

Step 2

Remove the sparkplug boot that covers the sparkplug of your leaf blower and you should have the ability to see the sparkplug under it. To remove the sparkplug, take the correct sized socket, fit the on the sparkplug and simply revolve the socket until the sparkplug becomes loose. Remove the sparkplug native the sheet blower engine and place it somewhere clean.

Note: Make sure to save the sparkplug boots away from the sparkplug hole when the sparkplug is removed to prevent any type of oil from acquiring into the boot.

Note: If your sparkplug does no look ok test it and if required replace it. You can uncover a sparkplug tester here. You deserve to find brand-new sparkplugs here.

Step 3

With the sparkplug removed, the sparkplug hole will certainly act as a drainpipe to eliminate the overfill engine oil native the burning chamber. And to push the oil out from the burning chamber to resolve your hydro locked leaf blower, merely pull the starter cord of her leaf blower. It can take a small force to pull the cord however you will an alert oil coming the end of the sparkplug hole once you traction the starter cord. Save pulling the starter cord swiftly until engine fluid stops coming the end of the sparkplug hole. This method that you have actually fixed the hydro lock and also your leaf blower’s engine is cost-free from overfill oil in the head cylinder.

Note: Oil might also come out of themuffler of your leaf blower together you pull the starter cord so don’t scare if yousee oil coming out of the exhaust together well.


Step 4

Once you space sure the all the oil has actually left the burning chamber spray some quick start liquid into the sparkplug feet to aid the engine to turn over easily. Make certain you spray the quick start in ~ an edge to make certain it it s okay to the cylinder.

Step 5

Fit the sparkplug ago into the sparkplug feet after cleaning the oil native the hole and also reconnect the sparkplug cable onto the sparkplug.

Step 6

Try to start the leaf blower and with fast start liquid in the cylinder head, the leaf blower engine should startup after ~ a couple of pulls. Now don’t scare if you see a many smoke coming out of your leaf blower’s exhaust since leftover oil in the burning chamber is being charred up bring about excess smoke. Keep the leaf blower running until the smoke clears out.

The hydrolock can also be brought about by overfill fuel gaining into the engine of her leafblower and also you have the right to use the above-mentioned procedures to eliminate excess fuel indigenous theleaf blower engine as well. You have the right to avoid hydro lock through making certain that youare putting the correct amount the oil inside her leaf blower and also when usingthe primer, make sure not to pump so much fuelinto the cylinder the it end up being hydro locked.

Spring inside the pull starterassembly is not functioning properly

The pull starter on her leaf blower provides aspring to wind increase the rope after you have actually pulled it. Yet if the feather getsbroken, the pull starter mechanism can get stuckand you won’t have the ability to pull the starter cord. Now unlike the traction cord thatcan be changed without acquisition the entirety pull starter assembly apart, friend willhave to remove the finish starter assembly to replace the spring. It deserve to bedifficult to uncover the correct sized feather that would certainly fit her leaf blower’spull start kit. So it is best to change the totality pull starter assembly. Afteryou have discovered the correct pull starter assembly for her leaf blower here ishow you deserve to replace it:

Step 1

Remove the starter assembly indigenous the leaf blower and also place the on a table.


Step 2

Make sure to eliminate all the stress from the traction starter assembly prior to removing the screw ~ above the starter assembly. And to do that merely remove the rope indigenous the pull handle and also let the spring unwind. In instance of a damaged or stuck spring, the starter assembly could not unwind on its own, and also in this case, girlfriend will have to manually revolve the assembly in the direction where the cord would certainly unwind native the reel to make certain the feather is not wound up once you remove the assembly as it deserve to flare out and cause one injury. If the assembly is damaged you can find a new starter assembly here.

Step 3

Now all you have to do is simply undo the screw in the middle of the pull starter assembly and also tap the starter assembly housing on a table come safely eliminate the assembly indigenous the housing. You have to avoid removed the assembly directly because the spring can flare up an extremely rapidly and it deserve to be dangerous.

Step 4

After closely removing the poor spring in addition to the starter assembly, right the new starter assembly into the traction starter real estate making sure the hook top top the spring of the new assembly fits top top the slot in the housing. Currently tighten increase the screw in the middle of the starter assembly to host the new assembly come the housing.


Step 5

Now just put the traction cord of the brand-new pull starter assembly with the hole because that the cord in the housing, connect the take care of to the finish of the rope and fit the housing ago onto the leaf blower and also you should have the ability to pull the starter cord without any problem.

You deserve to just replace the damaged spring too instead of replacing the entirety starter assembly. But it deserve to be challenging to find the right-sized spring and also installing the spring into the starter assembly have the right to be extremely difficult. If the assembly is damaged you can find a brand-new starter assembly here.

The engine has seized

If a leaf blower has been to run without ideal lubrication then it deserve to seize up and also the piston will stop relocating inside the cylinder. In this case, the traction cord will also get stuck and also won’t pull because the piston has actually seized against the cylinder walls. Unfortunately fixing a seized sheet blower have the right to be costly and also it generally requires assist from a mechanic because committed tools are essential to resolve a seized sheet blower engine. But if your leaf blower has actually run out of oil while it has been sitting and also not being offered you might be able to fix that by including some engine oil to it and pulling the starter cord again to check out if the engine turns over. Yet in most cases, a seized leaf blower engine will call for a complete engine rebuild.

You deserve to find an excellent leaf blower oil here.

See more: Degrassi Couples That Dated In Real Life, Best Degrassi Couples

Conclusion

Now that youknow the feasible causes and also fixes because that a stuck sheet blower traction cord, girlfriend can conveniently diagnose and also repair your leafblower’s pull starter assembly in ~ home. Store in psychic that part leaf blowersmight have actually a slightly various design, makingthe repair procedure different for each leaf blower model. Yet the straightforward workingmechanism that the traction starter system for each kind of leaf blower is thesame and you have the right to use the above-mentioned repair to fix your sheet blower’sjammed pull cord.