These instructions use to keywind pendulum clocks that space time only, or that have hour strike, or hour and also half-hourstrike. When written particularly for Connecticut form spring thrust clocks, portions are applicable to German andFrench clocks and American layout Japanese clocks. The to win synchronization instructions use to counting wheelstriking, i beg your pardon is not self-synchronizing.

SETUP and also OPERATION

Mantel Clock Setup:

Place clock top top table with back facing you. Open the back door, cave the pendulum top top the hook, and also close the door.Carefully place the clock wherein it is to be used, top top a stable, level surface. Lift one next of the clock gentlytwo inches, then placed it down, to begin the pendulum swinging.

Shelf Clock Setup:

Place the clock wherein it is to it is in used, ~ above a stable, level surface. Open the front door and also hang the pendulumon the hook (on plenty of clocks the hook is behind the dial), give the pendulum a swing, and also the clock will startticking.

Wall Clock Setup:

Choose the appropriate size hardwood screw (typically a #8, 10 or 12) come fit the hanger at the top back of the clock, andlong enough to go securely through the wall surface into a stud. Secure the screw into the wall, angled upward at a 45degree angle, and also hang the clock. Open the front door and hang the pendulum on the hook (on countless clocks the hookis behind the dial), provide the pendulum a swing, and also the clock will begin ticking. Relocate the bottom that the caseto the left or right until ticking is also (or if there is a beat scale beneath the pendulum, relocate the instance sothe pendulum points come zero when at rest). Secure bottom of case to wall so clock is stable.

Setting the Hands:

When setup the clock to time, relocate the minute hand, pausing at every hour (and half-hour for part clocks) forthe clock come strike. Never move the hands counterclockwise previous 6 or 12.

Winding - Eight work clock:

Wind the clock when per week, best on the exact same day every week. Rotate the key with a smooth motion, stoppingwhen the spring is tight (approximately 7 transforms after one mainly of running). Never ever let the vital snap ago in yourhand, constantly release it gently after each half turn. Make certain the clock is fully wound, so save turningthe crucial until the spring is clear tight. The left square winds the to win mainspring and, the rightsquare winds the time mainspring.

Winding - one day clock:

Wind the clock when each day, preferably at around the exact same time each day. Rotate the vital with a smooth motion, stoppingwhen the feather is tight. Never let the an essential snap ago in your hand, always release it tenderness after each fifty percent turn.The left square winds the win mainspring and the best side winds the moment mainspring.

Winding Direction:

Timekeeping Accuracy:

This kind of clock will be able to keep time in ~ 4 minutes per week. Friend will need to do the last regulationonce the clock is in the permanent ar to attain this accuracy. To examine the clock"s accuracy, set the handsto the exactly time, and also then allow the clock run at the very least 3 or 4 days. The main factors causing sports in rateare temperature changes, and also the lessening stress and anxiety of the mainspring together it operation down. When the clock is regulatedto keep good time, girlfriend will need to collection the hands whenever the time is turn off by more than a couple of minutes - perhapsevery week or two.

Regulating the clock - regulation Square:

The clock deserve to be made come go much faster or slower by way of the small square on the dial. Transforming it towards F increases the clock, and transforming it towards S slows the down. Turn the square just a little amounteach time. The regulation square is turned v the small end that the winding key.

Regulating the clock - Pendulum Nut:

The clock deserve to be made to go much faster or slower by way of the nut in ~ the bottom that the pendulum. Transforming the frontof the seed to the right speeds up the clock, and turning it to the left slowly it under (in other words move thenut up to speed up, or down to slow down). Revolve the nut only a small amount every time.

Alarm Setting:

On most American antique clocks, the alert is collection by turning the disc in the center of the dial. Revolve the discso that numeral of the hour you desire the alarm to ring is situated under the hour hand. Then wind up the alarmmechanism (usually located in the reduced left the the clock case). Over there is no alert shutoff mechanism, for this reason whenthe alarm starts ringing, it will ring till it runs down.

ADJUSTMENTS

Strike Synchronization using hands:

If the win gets out of synchronization v the hands, wind up the strike spring (left winding square), thenproceed together follows. Move the minute hand forward to two minutes prior to the hour. (The strike train renders a noisecalled the warning.) relocate the minute hand backwards to 15 minutes prior to the hour. The clock will certainly strike. Repeatuntil the variety of hours win is one much less than the hour that the hour hand points to.

Strike Synchronization using wire:

If the to win gets the end of synchronization v the hands, wind up the strike spring (left winding square), thenproceed together follows. Rotate the minute hand front to the following hour. When striking stops, push up (or pull downon some clocks) the small wire hanging beneath the dial and also let the clock strike. Each time you push (or pull)the wire, the clocks will certainly strike the following hour. Repeat till the correct hour is struck.

Strike Sound Adjustment:

The hammer i m sorry strikes the gong may have its shank bent contempt by hand to make the hammer head closer to orfurther native the gong, to do it sound pleasant.

If clock does no run:

1) Make certain clock is totally wound. 2) Make sure clock is ticking evenly. Make certain clock is ona stable surface and does no rock. If vital shim one or 2 corners v cardboard (for a shelf or mantelclock), or move bottom of clock come left or ideal (for a wall clock). 3) Make certain minute hand is not recorded onhour hand.

MOVING THE CLOCK

always remove the pendulum prior to transporting the clock, to protect against damage.

MAINTENANCE

Three Year Oiling and also Inspection:

Your clock, gift a precision mechanism, needs periodic maintenance to store it running reliably and to give itlong life. We recommend the following: After using it for 3 years, lug the clock in for oiling and also inspection.We will examine the condition of the movement, and also check that the mainspring ratchets room secure. We will tell youif the clock needs an overhaul, or will certainly be it s okay for several an ext years.

Overhaul:

Windup clocks require overhauling about every 3 - 7 years. The setting in i beg your pardon the clock is offered plays a bigrole in exactly how long it will run in between overhauls.

Why her clock won"t operation forever:

As dust it s okay in the mechanism, the oil i do not care an abrasive paste which reasons wear. The longer the clock runsin this condition, the much more repair it will certainly need. Numerous American clocks have actually very solid mainsprings which willrun the clock because that years after the oil has gone bad, leading to severe wear to pivots and also pivot holes. If your clockstops and also you spray it through oil to make it go again, that will proceed to undertake badly, due to the fact that it is tho dirty.Shortcuts prefer cleaning the motion whole, even using an ultrasonic cleaner, cannot effectively clean pivots, pivotholes, and mainsprings. These techniques simply postpone the need for a appropriate overhaul.


You are watching: How to set a seth thomas clock


See more: Can I Color My Hair Before Surgery !: Hi Everyone Can, Dye Hair Before Surgery!: Hi Everyone Can

How we overhaul her clock:

The activity is take away apart and also cleaned, the pivots polished, worn pivot feet bushed, worn the end pinion wires replaced,the mainspring ratchets checked and also repaired, any type of other important repairs lugged out, and the mainsprings checked.Then the parts are cleaned again, the pivot holes cleaned through pegwood, the pivots given last cleaning, and also thenthe activity is assembled and also lubricated.