Hello, I'm Danny.Glad to hear you like our site! right here is a indict showing exactly how to replace a serpentine belt:https://www.gimpppa.org/articles/replace-serpentine-beltI've attached picture steps below on how to remove and also replace both the engine and also A/C serpentine belt for your truck. Expect this helps and also thanks for making use of gimpppa.org.


You are watching: 2009 chevy silverado serpentine belt diagram

*

*

*

*

*

environment Procedure 1. Install the journey belt. 2. Course the drive belt end and/or roughly all the journey pulleys other than for the tensioner. 3. Download a 3/8 inch breaker bar into the tensioner opening and rotate the tensioner counterclockwise. 4. Download the belt end and/or around the tensioner. 5. Gradually release the stress and anxiety on the tensioner arm. 6. Check the drive belt for suitable installation on and/or roughly all pulleys. 7. Place the engine cooling pan shroud on the 3 mounting brackets (1).
Hello, I'm Danny.If the pulley-block bolt is stripped girlfriend will have to remove the totality assembly come replace. Here are a couple of tutorials to see showing exactly how to replace the serpentine belt and also tensioner:https://www.gimpppa.org/articles/replace-serpentine-belthttps://www.gimpppa.org/articles/serpentine-belt-tensioner-replacementI've attached photo steps below on exactly how to remove and replace both the serpentine belt and the tensioner for your truck. Hope this helps and thanks for using gimpppa.org.
The manufacturers say if over there are an ext than 3 cracks within one inch, it should be replaced. However, I discover that tough to believe. ~ above average, civilization usually get about 35K out of one. Remember, if there room superficial crack in it, in my publication that is normal wear. If that starts cracking with the threaded component in the middle, I would certainly recommend instead of it.Let me know if you have actually other questions.Joe
I have replaced every pulley, belt tensioner, and belts on mine Chevy Silverado 2500 HD over a duration of the critical 2 years. I have no noise after every repair, however it start squeaking again after ~ a few minutes to occasionally a few days every time I fix it. Could something be the end of alignment? that is really irritating to have the same noise come earlier time and time again.I have had at least 5 various mechanics work on it and each time ns think the is fixed, the noises come back. The critical time I placed a new belt on, that went great for around 100 miles.I wash the truck and also the belt started squealing.Then after the dried the end it quit for a pair of days, yet then began up the chirping again again. It it s okay worse as the engine warms up and is torquing up.
I likewise have a 2005 Silverado only mine is a single cab work-related truck. Mine belt squeaks too, I have replaced the pulleys and also the belt the squeaking stopped for awhile however came back. The only solution i have uncovered is Brake Cleaner. I placed it top top the belt and it quit the squeaking for 2 to 3 weeks yet it is doing that again!


See more: ⚡ 2021 ▷ ¿Cuál Es La Ubicación Filtro De Gasolina Dodge Ram 1500

Hi,Replacing the serpentine belt isn't a daunting job. First, right here is a attach that defines in general how it's done. You can use this together a guide.https://www.gimpppa.org/articles/replace-serpentine-beltHere room the directions certain to your vehicle. The fastened pics correlate with the directions.________________________________________2005 Chevy truck Silverado 1500 4WD V8-5.3L VIN B journey Belt replacement - AccessoryVehicle Engine, Cooling and Exhaust Engine journey Belts, Mounts, Brackets and also Accessories drive Belt Service and also Repair steps Drive Belt instead of - AccessoryDRIVE BELT instead of - ACCESSORYDrive Belt instead of - Accessory (4.8L, 5.3L, and also 6.0L Engines)Removal Procedurepic 11. Ease the air cleaner outlet duct clamps at the complying with locations: The accelerator body The mass Airflow/Intake air Temperature (MAF/IAT) sensor 2. Disconnect the radiator inlet hose clip from the outlet duct. 3. Remove the air cleaner outlet duct.pic 24. Download a breaker bar v hex-head socket to the drive belt tensioner bolt. 5. Turn the journey belt tensioner clockwise in order come relieve tension on the belt (1). 6. Remove the belt (1) indigenous the pulleys and the drive belt tensioner. 7. Gradually release the anxiety on the journey belt tensioner. 8. Remove the breaker bar and socket and from the drive belt tensioner bolt. 9. Clean and inspect the belt surfaces of all the pulleys.Installation Procedurepic 31. Path the journey belt (1) roughly all the pulleys except the idler pulley. 2. Download the breaker bar with hex-head socket to the belt tensioner bolt. 3. Turn the belt tensioner clockwise in stimulate to relieve the stress on the tensioner. 4. Download the journey belt (1) under the idler pulley. 5. Slowly release the tension on the belt tensioner. 6. Remove the breaker bar and socket indigenous the belt tensioner bolt. 7. Check the drive belt (1) for ideal installation and alignment.pic 48. Align the arrow (2) at the accelerator body end of the duct v the accelerator body it is registered stud (1).pic 59. Install the waiting cleaner outlet duct.10. Connect the radiator inlet hose clip come the outlet duct. Notice: describe Fastener notification in business Precautions.11. Tighten the waiting cleaner outlet duct clamps at the adhering to locations: The accelerator body The MAF/IAT sensor Tighten the clamps to 4 Nm (35 inch lbs.)._________________________I hope this helps Let me understand if you have other questions.Take care and God Bless,Joe