Hello, Ths distributor is located back by the distributor. Check out the diagrams (Below). Please let us know if you require anything rather to acquire the problem fixed.


You are watching: 2000 chevy s10 4.3 oil pressure sensor location

*

*


my fuel pump stop working.I"ve replaced it yet still won"t work. Looking through my publication a little closer I uncovered that if the oil press switch goes out it will certainly shut off strength to the fuel pump. What I need to recognize is where the oil press switch is and the an obstacle in an altering it. Or might there be one more problem? Fuses and relay is good.

perform you hear the fuel pump come on because that 2secs when key at operation position. If not examine fuse and fuel pump relay.The fuel pump and also oil press sending unit is located on appropriate side the engine

*



Engine mechanical problem1997 Chevy S-10 4 cyl two Wheel Drive manual My fuel pump has shut down and the truck no start. I"ll revolve the key but can"t hear any whirring from the fuel tank. I"m trying to inspect my bases prior to draining the tank and also pulling the fuel pump. Would certainly the oil press switch completely shut down the fuel pump or cut the press in some other way? ns was said to check the oil pressure switch, is there a method to check it or execute I simply replace it?
Oil push switch would certainly not shut off fuel pump, but the fuel pump has actually a second route through the oil press switch. If the fuel pump relay goes out the pump will then run with the oil push switch after ~ the engine it s okay oil pressure. This results in prolonged engine cranking time before the engine will start. Have you inspected every fuses, inertia switch (if equipped), relays and wiring prior to going in because that a pump replacement? Repalce her oil pressure sending unit. Thanks for utilizing gimpppa.org. Com!
I have actually a 97 s-10 4.3 we readjusted fuel pump and relay currently truck wont begin cranks over hard starts periodically wondering if oil press switch is problem
examine the fuel pump and also oil push sending unit this is the one that powers the fuel pump as soon as the engine fires up.
ns am having a difficulty w/ the oil pressure switch I have actually all ready placed in a new one and also I still get the exact same result. The oil push gauge is all the method to the right. I additionally replaced the fuel pump, ecm or computer, and the fuel relays. I replaced the fuel relays in the glove box I thought there might be fuel relays in another location but I might not uncover them, space there relays in an additional place besides the gloves box? i drove the van to my home a month ago and acquired it to start about a week ago but currently it turns over yet will no start. I know a great amount about cars yet this one is relay giving me problems I cant figure out what ns am missing. Perform you recognize what can be causing the oil pressure gauge to simply stay stuck to the right like this?
hi there, friend will have to an initial check the the oil push is with in specs through a mechanical gauge, if the is ok, the difficulty will be in the wiring, start here.Mark (mhpautos)
where is the oil press sending unit on mine truck listed above (2.2)? Also, if that is poor would this make it display no press on the gauge?
See below for location.Check the oil pressure with a mechanically gauge, if normal change the oil pressure switch. If abnormal can mean oil pump and engine bearing.
The sending out unit is ~ above the ideal rear side of your engine. If that were bad then girlfriend would present low or no oil pressure. Yet to it is in sure placed a mechanically gauge top top the engine to watch if it is exactly or not.
Hello, here is what the publication saysOil press Switch (2.5L/4-151): RH rear of Engine, Under ManifoldOil press Switch (2.8L/V6-173): lower LH side of EngineOil press Switch (4.3L/V6-262): RH behind of Engine please let us know if you need anything else to get the difficulty fixed.
I have actually a Fuel Problem, Started as soon as the fuel pump died. Changed the pump, Cleaned up the ground. Pump does not come ~ above at rotate of key. Dad said might be oil push switch. Wherein is it and how do you inspect it? I have switch approximately the relays under the hood and in gloves box. Did not assist still no pump noise. Any type of suggestions?Thank you.
When first key ~ above fuel pump should come on for a min if not inspect wiring and also connector plug Fuel Pump/Oil pressure Switch situated On ideal side the engine, behind alternator.
I have a 1993 chevy s10 through a 2.8L engine in it. The oil press sensor go out out of the next of the motor and also I changed it. Currently my inquiry is how come once I changed it and plugged it increase up the fuel pump came on even when the ignition to be off and also the an essential out of it and didnt rotate off till I unplugged the oil pressure sensor. Have the right to someone please assist me.
Sounds prefer you have the wrong sending out unit, it had two terminals reversed once it to be made, or the plug is in backwards.GM had some solution that ran the fuel pump off a terminal ~ above the sending out unit together a safety and security cutout. If the vehicle was in a crash that ruptured a fuel line, there would certainly be no fuel pressure so the engine would certainly stall. When it stalled, there would certainly be no oil press so the move in the sending unit would revolve off and also turn off the fuel pump. That would protect against it from pumping raw fuel onto the ground.
for this reason why is the fuel pump comes on and also staying on as long as tht sensor is plugged up also when the ignition is off? also the van wont even start because that oil press sensor go out and also I replaced it.
i agree v doc top top the truth that you likely have actually either a negative or the not correct oil sender. That is provided as a redundant strength supply for the fuel pump however it IS no a short pressure reduced off. The does not have actually the capacity to interrupt the fuel pump, it can only power it in the case of a relay failure.
I have actually A 2001 S10 2.2l and also I"ve changed The Engine. As soon as I start It increase It Sounds like A Tractor. Don"t Think it Is one Exhaust Leak I"ve...
I have A 2003 S-10 Pickup through A Vacuum Leak and Am in search of A Piping Diagram so I have the right to Replace negative Vacuum Lines


See more: What Happens If You Mix Semi Permanent Hair Color With Developer

My Fuel Pump Went the end I need The Diagram because that The Fuel Pump Relay Switch. The Still will Not Start. No strength To The Pump.